ICarsoft CR Pro is a Professional and powerful vehicle fault diagnosis tool for multi-brand vehicles (more than 40 kinds of vehicle makes) developed by iCarsoft Technology Inc. With a 4.0 TFT LCD and unique diagnostic software, it features full ECU diagnosis of most vehicle brands and test modes mainly include: CANBUS, ISO9141, KWP2000, and J1850 etc.
It enables technicians to accurately diagnose complex problems. CR Pro vehicle coverage: Nissan, Infiniti, Toyota, Lexus, Scion, Honda, Isuzu, Hyundai, Kia, Daewoo, Mazda, US Ford, Sprinter, BMW, Mini, VW, Seat, Skoda, Volvo, Porsche, SAAB, EU Ford, Holden, AUS Ford, Acura, Subaru, Mitsubishi, Dacia, Renault, Fiat, GM, Chrysler, Mercedes-Benz, Citroen, Jaguar, Peugeot, Audi, Opel, Land Rover, Smart, Suzuki, Vauxhall, Alfa-Romeo, Lancia. CR Pro is the updated version of CR Plus. CR Plus works on 4 systems, CR Pro works on full systems.
CR Plus supports 3 special functions, CR Pro supports 8 special functions + more under development. ICarsoft CR Pro can do it all-reads and clears trouble codes on most of the systems such as. Engine, transmission, ABS and Airbag etc. Support OBDII/EOBD Ten Modes of Operation. Applies to most of the vehicle models which equipped with OBDII-16 DLC. Easy To Use with Silicone Keys. Oil Light/Service Reset: Support service lamp reset. Electronic Parking Brake (EPB) system maintenance deactivates and reactivates the EPB system. Battery Management System (BMS), registers new battery to the BMS while battery replacement. Diesel Particulate Filter (DPF) regeneration control system. Requests the DPF regeneration process while DPF blockage and turn off the DPF indicator. Electronic Throttle Control system (ETC) relearns the throttle valve control value while clear. Or replaces the throttle valve. Steering Angle Sensor (SAS) calibration, calibrates the steering wheel to straight ahead, or recalibrates.ABS Bleeding, release the air to restore ABS Brake sensitivity, or relearn while ABS replaced. Injector coding, relearn the injector control parameter while the injector renewed or replaced. SAS while steering part replacement. The Print Data function allows you printing out diagnostic data recorded by the scan tool or. Battery test allows you getting the voltage of battery with OBD port by the scan tool when.
DTC Library to lookup when user is operating this tool. English, French, Deutsch, Spanish, Dutch, Italian, Czech, Hungarian, Polish, Swedish, Finnish, Portuguese, Russian, Danish, Norwegian & More. A special factory access code.
This scan tool covers over 20 years of models, so some functions may not be available. On vehicles where a manual reset is required, the tool will guide you through the full process step-by-step.
This electric parking brake (EPB) function has a multitude of uses to maintain the electronic braking systems safely and effectively. The applications include deactivating/activating the brake control system, assisting with brake fluid control, brake diagnostics, opening and closing brake pads, setting brakes after disc or pad replacement and also reading and clearing EPB/SBC trouble codes. It is also capable of retrieving Fault Codes information from the ECU. Carry out a forced Diesel Particulate Filter (DPF) Regeneration on supported vehicles - this MUST be done by trained personnel.
Required when the DPF filter blockage reaches levels where passive or active regeneration is unable to burn off the excess soot. The Steering Angle Sensor (SAS) is used to measure the angle of the steering wheel and the speed at which it is being turned. The signal is mainly used by the ABS System as part of it's stability control function but also by other systems such as ride level control and adaptive lighting. A problem with the SAS Signal will cause a fault with any of the systems that use the signal directly, or indirectly. If the Steering Angle Sensor (SAS) needs to be changed, many vehicles require the new sensor to be calibrated.The iCarsoft CR PRO will allow you to carry out steering angle re-calibration on supported models. Electronic Throttle Control system (ETC) relearns the throttle valve control value while clear or replace the throttle valve.
Display: 4.0 TFT LCD, 480320 Pixels. Power Consumption: 1.8W (Typical).
Dimension: 206104.132.6 mm (L x W x H). TF Card (Within the main unit). The item "ICARSOFT CR PRO FULL System ALL Makes Diagnostic Tool + Extra Features 2021" is in sale since Thursday, February 18, 2021.
This item is in the category "Vehicle Parts & Accessories\Garage Equipment & Tools\Diagnostic Equipment & Tools\Code Readers & Scanners". The seller is "ariautoparts" and is located in Wednesbury. This item can be shipped to United Kingdom, Antigua and barbuda, Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Australia, United States, Bahrain, Canada, Japan, New Zealand, Israel, Hong Kong, Norway, Indonesia, Malaysia, Mexico, Singapore, South Korea, Switzerland, Taiwan, Thailand, Bangladesh, Belize, Bermuda, Bolivia, Barbados, Brunei darussalam, Cayman islands, Dominica, Ecuador, Egypt, Guernsey, Gibraltar, Guadeloupe, Grenada, French guiana, Iceland, Jersey, Jordan, Cambodia, Saint kitts and nevis, Saint lucia, Liechtenstein, Sri lanka, Macao, Monaco, Maldives, Montserrat, Martinique, Nicaragua, Oman, Pakistan, Peru, Paraguay, Reunion, Turks and caicos islands, Aruba, Saudi arabia, South africa, United arab emirates, Ukraine, Chile, Bahamas, Colombia, Costa rica, Guatemala, Honduras, Jamaica, Kuwait, Panama, Philippines, Qatar, Trinidad and tobago, Uruguay, Viet nam.